3D Simulation Results: Model: IRI
Run: Ola_Abuelezz_011121_IT_12

This is the web interface for the visualization of results of a three-dimensional simulation of the Earth's environment.

Note: Floating-point values with a decimal point not followed by numbers (e.g., "1." or "1.E+4") are not being accepted. Please enter equivalent values ("1.0" or 1.0E+4) or ("1" or "1e+4") instead.
Please review the default selections below and make your changes.

To start the graphics program click the Update Plot button. The resulting image will be displayed at this location of the page.

Should the result be a black image, then the graphics program encountered a programming error. Please report the set of input parameters used.

Go back to web page of run

Update Plot will update (generate) the plot with the chosen time and plot parameters below.
This will take some time (typically 10-30s) as data are read in and processed.

Choose data time:

Change time (relative to selected time above)

Create GIF movie (and archive of ASCII data outputs) with current plot settings

Start Time:
End Time:
Stride (skip time steps):
Some simulations are long and cannot be processed all within two days or may overflow the capacity of our temporary file system. We have to limit the number of time steps requested at any one time to 3000.
We are working on imcreasing our capabilitie and apologize for the inconvenience.
Email address for notification (replace the example email address with yours):
@
Note: The movie will be requested but NOT be shown in this interface. You will get an email with a download URL when the request has been completed (this will take at least a few minutes).
Only one request can be pending at a time for each client IP or email address. Movies and Images remains on the ftp server for a week and need to be downloaded within that time.

Choose Plot Mode:

Show advanced options

Choose quantity to be displayed:

Q 1:

Q 2:

Q 3:

Customized variables are possible!
Email the formula that you would like to see and that uses existing quantities to Lutz and it will be tested and added.

Plot Options for selected Plot Modes:

3D-Surface/EarthView, 3D-Flowlines, Color Contour on Sphere:
  View angles:
   AX [-90..90]: (viewer's elevation angle)
   AZ [-180 ... 180]: (viewer's azimuth angle; 0: along negative Y)

Color Contour:
   Color table:
New:new tables added: cividis, viridis, magma, plasma, inferno.
   Reverse Colortable
   Number of levels:

Lock color range:
Min.: Max.:
Log scale (use all data>0 in non-negative fields)

Contour:
show values with contour levels
Number of Levels

Lock range:
Min.: Max.:
Log scale (use all data>0 in non-negative fields)

Choose Plot Area:

Choose Cut Plane:

lon₁	lon₂	Range: 0 ... 360 deg	lon=constant
lat₁	lat₂	Range: -90 ... 90 deg	lat=constant

H₁

H₂

Range: 100 ... 1000 km

H=constant

New: Render ensemble of similar plots using the following runs
(enter up to 3 names of runs in the same run category (solar, heliosphere, magnetosphere, etc.) into text fields below):
Runs should be of the same model or using the same coordinates. Comparisons of magnetosphere runs may be best done requesting one of the magnetosphere coordinate systems (SM, GSM or GSE in the Render Oblique Cut Plane section).

Consider nearest date and time within seconds (<60).
Number of plots in table row:

Render polar plot with maximum colatitude:

10° in latitude, 30° in longitude - override display of simulation grid

Reset Form will reset changes to the defaults specified by the previous run of this script.
Update Plot will update (generate) the plot with the chosen time and plot parameters above.

List Data (check to get any of the following outputs which apply to movie requests as well):

Runs-on-Request:
Visualization:
Last modifield: 2024-07-23

3D Simulation Results: Model: IRI Run: Ola_Abuelezz_011121_IT_12

This is the web interface for the visualization of results of a three-dimensional simulation of the Earth's environment.

3D Simulation Results: Model: IRI
Run: Ola_Abuelezz_011121_IT_12