3D Simulation Results: Model: IRI
Run: vivek_g_112020_IT_1

This is the web interface for the visualization of results of a three-dimensional simulation of the Earth's environment.

Note: Floating-point values with a decimal point not followed by numbers (e.g., "1." or "1.E+4") are not being accepted. Please enter equivalent values ("1.0" or 1.0E+4) or ("1" or "1e+4") instead.
Please review the default selections below and make your changes.

To start the graphics program click the Update Plot button. The resulting image will be displayed at this location of the page.

Should the result be a black image, then the graphics program encountered a programming error. Please report the set of input parameters used.

Go back to web page of run

Update Plot will update (generate) the plot with the chosen time and plot parameters below.
This will take some time (typically 10-30s) as data are read in and processed.

Choose data time:

- or -
Change time by moving
output steps

- or -

Create GIF movie (and archive of ASCII data outputs) with current plot settings
Note: This is a queue submission system requiring the following three additional inputs:

Start Time:
End Time:
Stride (skip time steps):
Email address for notification (replace the example email address with yours):
@
Note: The movie will be requested but NOT be shown in this interface. You will get an email with a download URL when the request has been completed (this will take at least a few minutes).
Only one request can be pending at a time for each client IP or email address. Movies and Images remains on the ftp server for a week and need to be downloaded within that time.

Choose Plot Mode:

Plot Options:

Show Continents

Image magnification
(all images; use >=1.25 for 3D Flowlines)

Line thickness (flow lines, arrows)

Character thickness (all annotations)

Allow variable plot image size
(all 2D plots: aspect ratio dx/dy between 0.3 and 4)

Show simulation grid (disabled with 3D-Surface/EarthView)

Interpolate data onto equidistant grid (available with 3D-Surface/EarthView)

New: Add satellite position to plot:
AEROCUBE-6A AEROCUBE-6B AIM
Akebono Aqua Arase (ERG)
Aura CALIPSO CASSIOPE
Cloudsat DMSP-15 DMSP-16
DMSP-17 DMSP-18 FAST
FIREBIRD 3 FIREBIRD 4 GCOM-W1
GOSAT GRACE-FO1 GRACE-FO2
Hinode ISS MetOp-B (MetOp-1)
MetOp-A (MetOp-2) NOAA-15 NOAA-18
NOAA-19 NOAA-20 Oersted
PARASOL RBSP-A RBSP-B
Reimei RHESSI SORCE
Suomi NPP Swarm A Swarm B
Swarm C THEMIS-A (P5) THEMIS-D (P3)
THEMIS-E (P4) TIMED
Note: Satellite positions are projected onto the selected cut plane if within the selected plot area.
Satellite positions may be far away from the selected cut plane.

Choose quantity to be displayed (some Plot Modes require up to two choices):

Q 1: Q 2:

Customized variables are possible!
Email the formula that you would like to see and that uses existing quantities to Lutz and it will be tested and added.

Plot Options for selected Plot Modes:

3D-Surface/EarthView, 3D-Flowlines, Color Contour on Sphere:
  View angles:
   AX [-90..90]: (viewer's elevation angle)
   AZ [-180 ... 180]: (viewer's azimuth angle; 0: along negative Y)

Color Contour, (Vertical) Line:
   Color table:
   Reverse Colortable
   Number of levels:
    Lock color range:
       Min.: Max.:
Log scale (use all data>0 in non-negative fields)

Contour:
    show values with contour levels
Number of Levels
    Lock range:
       Min.: Max.:
    Log scale (use all data>0 in non-negative fields)

Choose Plot Area:
  All Plot Modes except Line Plot and Vertical Plot:   Select lower left corner of plot area on the left, and the upper right corner on the right.
  Line Plot: Select start point of line on the left, the end point on the right.
  Vertical Plot: Select lon and lat position on the left.

Choose Cut Plane:

lon₁	lon₂	Range: 0 ... 360 deg	lon=constant
lat₁	lat₂	Range: -90 ... 90 deg	lat=constant
H₁	H₂	Range: 100 ... 1000 km	H=constant

Render polar plot with maximum colatitude:

10° in latitude, 30° in longitude - override display of simulation grid

Reset Form will reset changes to the defaults specified by the previous run of this script.
Update Plot will update (generate) the plot with the chosen time and plot parameters above.

List Data (check to get any of the following outputs which apply to movie requests as well):

What:

Plot variables from above
Include all primary model output parameters (Warning: text files may become large).
You have to select vector magnitudes (e.g., "B","V","J") explicitly for plotting to get them:
computed scalars such as
derived vectors (e.g, "JxB"): select one component or its magnitude to get all components

Include parameters from this list in addition to those selected for the plot: (copy names from Q1 list above and separate them with commas).

Where:

At positions specified: enter positions in lon, lat, H, (within the allowed range) as comma-separated lists.

List Data From Plot:

2D plots (Contour, Vector, ...):
equidistant 61x61-element grid in cut plane (Interpolate data onto equidistant grid selected)
max. 44000 grid positions (Interpolate data onto equidistant grid unchecked)
LinePlot: data along line plotted,

Runs-on-Request:
Visualization:

3D Simulation Results: Model: IRI Run: vivek_g_112020_IT_1

This is the web interface for the visualization of results of a three-dimensional simulation of the Earth's environment.

3D Simulation Results: Model: IRI
Run: vivek_g_112020_IT_1